NEW DAF E6 DELPHI ECU ETC3-PCX2 – Worldwide exclusive!
We are proud to announce that from today it will be possible to map DAF E6 D+ trucks registered from 2017 to 2021 equipped with the DELPHI ETC3-PCX2 control unit. At the moment this service is only available to you who use our Official FGTechnology EOBD2 system to...
MED17.8.10.1 – MED17.8.10 now available in Bench and Boot
FGtechnology EOBD2 now supports reading in Bench and Boot mode for MED17.8.10.1 and MED17.8.10. These ECUs are equipped on 1.0 and 1.5 T-GDI petrol engines of Ford, MG and Saic brands. Reading and/or writing can be done directly via PINOUT without having to open the...
Continental SID807 & SID807EVO PSA group now available in Full OBD
FGtech EOBD2 now supports reading and writing of all versions of Continental SID807 via OBD. Previously only writing in diagnosis was supported now full reading of flash and eeprom and writing for both versions has been implemented. ♦ Reading (Flash+Eeprom)♦ Writing...
Scania CNG now available reading in Bench
FGtech EOBD2 now supports Benchmode reading for Bosch EGC4.0 - EDC17CB25. These control units are equipped on CNG methane engines of the G410, P410 and R410 Series. With this update we have implemented the support of control units for the Scania brand, providing a...
Simos 8.x VW now available in Bench and Boot
FGtech EOBD2 now supports Bench and Boot mode reading for Simos 8.x. These ECUs are equipped on 3.0 TFSI petrol engines Reading and/or writing can be done directly via PINOUT without having to open the ECU and in bootmode. ♦ Reading (Flash+Eeprom)♦ Writing...
Continental MSD8x & MSV90 BMW Now Available in Bench
FGtech EOBD2 now supports reading in Benchmode on the bench for Continental MSD80,81,85,87 & MSV90. These ECUs are equipped on BMW petrol engines for example (N43B20, N52B30, N54B30, N54B30, N63B44, N74B60, S63B44) Reading and/or writing can be done directly via...
New JTAG protocol for MPC57xxx processors
FGtech EOBD2 now supports JTAG reading of new ECUs equipped with Freescale MPC5777 processor. This protocol is very useful in case of microprocessor block, therefore it allows to read the damaged and/or corrupted file and to restore and/or clone the ECU. New control...
Continental Simos 18.xx Vag group now available in OBD
FGtech EOBD2 now supports reading and writing of all versions of Continental Simos 18 via OBD. Previously only Simos18.1 version was supported, now all subsequent versions have been implemented (18.2-18.3-18.6-18.10). We have also added the functionality to downgrade...
1.2 Puretech PSA-Stellantis Engines now Supported in Bootmode
FGtech EOBD2 now supports bench reading in Bootmode Valeo V56.x and VD56.x units with Aurix processor. Now you can have a wide range of PSA-Stellantis group vehicles with 1.2 Puretech engine at your disposal. ♦ Read (Flash+Eeprom)♦ Write (Flash+Eeprom)♦ Chk List of...
VAG Gasoline Update/Restore original with FRF/ODX/SGO files
FGtech EOBD2 now supports reading and writing for Bosch MED17 VAG ECU via OBD. We have added new features to perform downgrades and upgrades to the software of control units fitted on Audi, Bentley, Cupra, Seat, Skoda, Volkswagen. Through this function EOBD2 allows...
VAG Update/Restore original with FRF/ODX/SGO files
FGtech EOBD2 now supports reading and writing of all Bosch EDC17 VAG ECUs via OBD. We have added new features to perform downgrades and upgrades to the software of control units fitted on Audi, Bentley, Seat, Skoda, Volkswagen. Through this function EOBD2 allows the...
CPC2 Powertrain Control Unit now supported
FGtech EOBD2 now supports bench reading in Bootmode of the Delphi CPC2 unit with TC1793 and TC1797 processor.This Powertrain control unit allows you to access the optimization of the parameters of the torque and speed limiters and modify the fluid flow inside the...
TCU/GEARBOX June 2024 update in Bench/Bootmode
FGtech EOBD2 now supports benchmode and/or bootmode reading of various TCU control units for a wide range of vehicles. These control units are equipped on vehicles from Audi, VW, BMW, FCA group, PSA group, Jaguar, Land Rover, GM, Ford and Volvo.In most cases reading...
TCU DQ381, DL501 & 7DCT300 TCUs now available in Bench
FGtech EOBD2 now supports Benchmode reading on the bench for DQ381 Gen1 and DL501 Gen1 TCUs. These control units are equipped on VW group vehicles; the reading for Getrag 7DCT300 TCU equipped by the BMW brand is also available. Reading and/or writing can be done...
Bosch EDC7-EDC16-ME9-MED9 cloning now available in Bench
FGtech EOBD2 now supports Benchmode cloning on the bench for all available Bosch EDC7-EDC16-ME9-MED9. Reading, writing and cloning can be done directly via PINOUT without having to open the control unit. ♦ Reading (Micro+Flash+Eeprom)♦ Writing (Micro+Flash+Eeprom)♦...
Meet us at AMTS – Auto Moto Turin Show
We are delighted to invite you to visit us at the AMTS - Auto Moto Turin Show, an event dedicated to all four-wheel enthusiasts! Unique vehicles will be on display, there will be a test drive track, and of course our FGTech team will be there to answer all your...
OBD reading for Iveco EDC7UC31 E5
FGtech EOBD2 now supports reading and writing the EDC7UC31 ECU via OBD.We carry out the reading and writing in Can-bus of the control unit via the diagnostic socket.Reading with K-line protocol and bench reading are already available. Supported vehicles list:Cursor...
OBD read for Fiat 1.2/1.4 gasoline engine
FGtech EOBD2 now supports reading and writing of the Marelli IAW 9GF ECU via OBD.We carry out the complete reading and writing of the control unit via the diagnostic socket.It is also possible to clone the ECU directly via OBD, bench reading is already available. List...
OBD read for Fiat and Lancia Hybid engine
FGtech EOBD2 now supports reading and writing the Marelli 11GF ECU via OBD.We carry out the complete reading and writing of the control unit via the diagnostic socket.It is also possible to clone the ecu directly via OBD. List of supported engines:0.9 Hybrid 70HP E6d...
MG1CA094 – MSE2 Bosch now available in Bench
FGtech EOBD2 now supports benchmode reading for Bosch MG1CA094. These control units are equipped on the KTM and Bajaj group motorbikes. Reading and/or writing can be done directly via PINOUT without having to open the control unit. ♦ Reading (Flash+Eeprom)♦ Writing...
TC60 & DQ500 MQB TCUs now available in Bench
FGtech EOBD2 now supports Benchmode reading on the bench for TC60 and DQ500 MQB TCUs. These control units are equipped on VW, Hyundai and Kia group vehicles Reading and/or writing can be done directly via PINOUT without having to open the control unit. ♦ Reading...
OBD read for DCM6.2AP Ssangyong
FGtech EOBD2 now supports reading and writing Delphi DCM6.2AP Ssangyong ECU via OBD.We carry out a complete reading of the control unit both via the diagnostic socket and also on the bench via PinoutIt is also possible to write the files read on the bench directly via...
OBD read for MED17.1.62 and Update FRF/ODX File
FGtech EOBD2 now supports reading and writing Bosch MED17.1.62 ECU via OBD. We have added new features to downgrade and upgrade the software of ECU systems mounted on Audi, Bentley, Seat, Skoda, Volkswagen. Through this function, EOBD2 allows the user to choose which...
DAF Euro 6 Full Read & Write Available
FGtech EOBD2 supporta ora la lettura e scrittura completa reale in OBD delle centraline Delphi ETC3-PCX2 equipaggiate sui mezzi DAF Euro6. La lettura reale della zona mappe a OBD era già disponibile. ♦ Lettura (Flash)♦ Scrittura (Flash)♦ Chk - Recovery Lista...
DQ250C & DQ500 TCUs now available in Bench and OBD
FGtech EOBD2 now supports bench-top Benchmode reading for TCU DQ250C and DQ500 MQB. These control units are equipped on VW Group vehicles. Real OBD reading is available for DQ250C gearbox The reading and/or writing can be done directly via PINOUT without having to...
Bench read for Land Rover Bosch MD1CP007
FGtech EOBD2 now supports benchtop Benchmode reading for Bosch MD1CP007 ECUs. This ECU is fitted to Land Rover/Range Rover 3.0d MHEV E6d vehicles. The reading and/or writing can be done directly via PINOUT without having to open the control unit. ♦ Readout...
Bench read for Continental Synerject M3A & M3C
FGtech EOBD2 now supports bench-top Benchmode reading for Continental Synerject M3A & M3C ECUs. These control units are equipped on a wide range of the latest generation motorcycles and scooters. The reading and/or writing can be done directly via PINOUT without...
Reading Kubota MB276000 ADBlue module
FGtech EOBD2 now supports benchtop Benchmode reading for Denso MB276000-00xx Kubota Adblue module. The reading and/or writing can be done directly via PINOUT without having to open the control unit. ♦ Readout (Flash+Eeprom)♦ Writing (Flash+Eeprom)♦ Chk & Recovery...
Ford SID803/803A Bench and EMS2102 Readout in Bootmode
FGtech EOBD2 now supports benchtop Fullmode reading for Siemens SID803 & SID803A Ford. The reading and/or writing can be done directly via PINOUT without having to open the control unit. ♦ Readout (Flash+Eeprom)♦ Writing (Flash+Eeprom)♦ Chk & Recovery List of...
Vag DCM6.2V reading on bench and FRF/ODX file update
FGtech EOBD2 now supports reading the REAL file of the DELPHI DCM6.2V ECU. The actual reading can be done directly via PINOUT without having to open the control unit. We have added new features to perform downgrades and upgrades to the software of control units fitted...
Bosch MSE6.0 & US6.0 now available on bench
FGtech EOBD2 now supports Bosch MSE6.0 & US6.0 ECUs in Benchmode. It will be possible to work on the bench on the new QUADs, ATVs and MOTORCYCLES. ♦ Read (Flash)♦ Writing (Flash Maps)♦ Chk List of Supported Vehicles:...
Suzuki Marelli 8DS now available on bench
FGtech EOBD2 now supports the MJD 8DS ecu in Fullmode. It will be possible to work on the bench on Suzuki Swift 1.3 DDis vehicles. ♦ Read (Flash+Eeprom)♦ Writing (Flash+Eeprom)♦ Clone♦ Chk♦ Recovery Bootmode BAM reads and writes have also been added. ♦ Read...
Fiat Marelli 8GSF – 8GSW MY>2018 now available on bench
FGtech EOBD2 now supports the ecu 8GSF - 8GSW MY>2018 in Fullmode. It will be possible to work on the bench on Alfa Romeo, Fiat and Lancia vehicles. ♦ Read (Flash+Eeprom)♦ Writing (Flash+Eeprom)♦ Chk♦ Recovery Bootmode BAM reads and writes have also been added for...
New OBD protocols for 1.5/1.6/2.3 dCi engines equipped on Renault, Nissan, Dacia & Opel.
FGtech EOBD2 now supports Siemens Sid310 control unit in OBD (Maps only), Obd Full is already supported. Now you can work on Renault, Nissan, Dacia & Opel vehicles equipped with 1.5/.1.6/2.3 dCi engine from 2012 to 2019 safely and at speed via diagnostic socket....
A LIST OF UPDATES COMING SOON AT FGTECH!
Starting from next week, a series of updates will be available for all our FGTechnology Users. We have listened to your requests throughout the last few years to be able to improve our products in order to make your work safer and more efficient. Let's start with the...
Fiat Marelli 9DF HW001-HW002 MY>2018 now available on the table
FGtech EOBD2 now supports 9DF HW001-HW002 MY>2018 ECU in Fullmode. It will be possible to work on the bench on Fiat, Alfa Romeo and Lancia vehicles. ♦ Reading (Flash+Eeprom)♦ Writing (Flash+Eeprom injector code)♦ Chk♦ Recovery Supported Vehicle List: ALFA...
ECU cloning with Tricore processors now available in BenchMode
FGtech EOBD2 allows you to clone ECUs equipped with Tricore processors in Benchmode without opening the ecu. Bosch, Delphi, Siemens & Continental can be easily cloned if the original ECU is damaged. This is possible thanks to a complete revision of the BENCHMODE...
Ford Bosch MG1CS036 now available in Bench
FGtech EOBD2 now supports Bosch MG1CS036 ecu in Benchmode. It will be possible to work on the bench on Ford vehicles powered by 2.3, 2.7 & 3.5 in safety and speed. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) List of supported vehicles: BRONCO 2.3 EcoBoost 300HP, 2.7 V6...
FCA Bosch EDC17C69 MY2021 & Marelli 9xx now available in Boot
FGtech EOBD2 now supports Bosch EDC17C69 MY2021 ecu and Marelli 9xx in Bootmode. It will be possible to work at the bench on Fiat, Alfa Romeo, Jeep, Suzuki and Chery vehicles. Available the Tricore bootmode for the new generation of EDC17c69 year 2021 and above and...
Renault E6d Bosch MD1CS016 now available in Bench
FGtech EOBD2 now supports Bosch MD1CS016 ecu in Benchmode. It will be possible to work on the bench on Renault, Dacia and Nissan vehicles powered by 1.5 & 2.0 dCi E6d in safety and speed. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) List of supported vehicles:...
Siemens-Continental SDI6-SDI8 Porsche now available in Bench
FGtech EOBD2 now supports the Siemens-Continental SDI8 ecu in Benchmode. It will be possible to work on the bench on Porsche 4.8L motorized vehicles safely and quickly. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) ♦ (Clone supported in Bench) List of supported vehicles: -...
New OBD solution for John Deere with PHOENIX L40 ECU!
FGtech EOBD2 now supports the Phoenix L40 ecu in OBD. This new solution will allow you to read and write the content of all new John Deere MY2022-My2023 tractors/agricultural machinery via the diagnostic socket. You will also be able to read and write the injector...
Siemens-Continental SID211 Ford now available in Bench!
FGtech EOBD2 now supports the Siemens-Continental SID211 ecu in Benchmode. It will be possible to work at the bench on Ford Transit vehicles safely and quickly. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) ♦ (Clone supported in Bench) List of supported vehicles: - FORD...
Siemens-Continental SID807EVO Ford/Volvo now available in Bench!
FGtech EOBD2 now supports Siemens-Continental SID807EVO ecu in Benchmode. It will be possible to work on the bench on Ford/Volvo vehicles in safety and speed. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) ♦ (Clone supported in Bench) Supported Vehicle List: - FORD B-MAX ...
Mercedes truck E6 MY2022/2023 now available in Fullmode.
FGtech EOBD2 now supports Continental MCM2.1 D5 version 2022/2023 ECUs. Now you can work on Mercedes Actros trucks safely and quickly. Versions MCM2, MCM2.1 D1/D2/D3/D4, ACM & ACM2.1 are already supported in Fullmode. Version MCM2.1 D5 must be unlocked in bootmode...
Exclusive Bootmode for Delphi DCM6.2V VAG!
FGtech EOBD2 now supports the Delphi DCM6.2V ecu in Bootmode BAM. It will be possible to work on the bench on all vehicles of the group with 1.4/1.6/2.0TDI engines in safety and speed. This protocol allows you to read and write the entire Flash memory to make the...
Ford SID209 2.2/3.2TDCI now available in Bench!
FGtech EOBD2 now supports Siemens-Continental SID209 ecu in Benchmode. It will be possible to work on the bench on all Ford vehicles with 2.2 & 3.2 TDCI engines in safety and speed. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) ♦ (Clone supported in Bench) Supported...
Fullmode for Trionic8 ecu and Bosch ME7.4.5 Psa
FGtech EOBD2 now supports new Fullmode for Trionic8 and Bosch ME7.4.5 ECUs. It will be possible to work on the bench on Saab 9-3 equipped with a 1.8/2.0 engine and a wide range of PSA Group vehicles with a 1.6 16V petrol engine. ♦ (Flash+Eeprom) ♦ (Chk) ♦ (Recovery) ♦...
Fullmode and Boot for Kubota/Manitou Tractors/Agricultural Machinery and much more.
FGtech EOBD2 now supports new Fullmode for Denso 112500-1xxx SH7058 ECU. It will be possible to work on the bench on a wide range of tractors, agricultural vehicles and construction equipment equipped with Kubota engines. In addition, new bootmodes and benchmodes for...
Benchmode and Boot for VAG Simos12, SID208 & EMS22xx Ford
FGtech EOBD2 now supports new Benchmode, Bootmode and new Clone Service functions for ecu equipped with Tricore processors. Following the list of new ecu present in the update. Supported ECU list: - Benchmode VAG Simos12 (micro TC1797); - Benchmode FORD Continental...
Clone service function available in the new EOBD2 version!
FGtech EOBD2 supports the new function to clone ECUs equipped with Tricore processors. Bosch, Siemens & Continental can be easily cloned in case the original ECU is damaged. Just load the files of the two Internal flash (Ecu ORI & Ecu NEW) and the software...
Mercedes truck E6 now available in Fullmode & OBD.
FGtech EOBD2 now supports Continental MCM2.1 D3/D4 control units. Now you can work on Mercedes trucks safely and quickly. MCM2, MCM2.1 D1/D2, ACM & ACM2.1 versions are already supported in Fullmode. The MCM2.1 D4 version must be unlocked in bootmode to enable...
JCB telehandlers now available in OBD & Boot.
FGtech EOBD2 supports the DCM2.7AP control unit in OBD and BootBAM mode. It will now be possible to operate a wide range of JCB brand telehandlers. Below is the list of new updates: New ECUs supported: - Delphi DCM2.7AP (OBD) - Delphi DCM2.7AP (BootBAM) Checksum,...
Reading AdBlue Mercedes and Delco GM in bench.
FGtech EOBD2 supports Adblue & Ecu ECUs in Bench mode. Now it will be possible to operate on a wide range of heavy vehicles of the Mercedes Benz truck and GM-Opel brand. Below is the list of new updates: New ECUs supported: - Ecu- ACDelco E67 (OBD Full & Bench...
Volvo-Renault truck AdBlue reading now available!
FGtech EOBD2 supports Adblue & Ecu ECUs in BootBAM mode. Now it will be possible to operate on a wide range of heavy vehicles of the Volvo-Renault Truck brand. Below is the list of new updates: New ECUs supported: - Ecu- Continental TRW EMS2.2 Euro5 SPC5554 (Boot...
Continental GPEC2,2A,3,4,4LM now available!
FGtech EOBD2 supports GPEC2,2A,3,4,4LM ECUs in BootBAM mode. Now it will be possible to operate on a wide range of petrol vehicles of the FCA group (Fiat, Jeep, Chrysler, Dodge). Below is the list of new updates: New ECUs supported: - Continental GPEC2 MPC5566 -...
New OBD, Bench, FullMode & BootMode protocols available.
FGtech EOBD2 now supports new ECUs in various modes, the list of new updates is shown below: New ECUs supported: - OBD Scania Continental EMS8-EMD1 real read and write tables/maps (full write already available) - Benchmode EDC7C1, EDC16C3, EDC16CP33 version with flash...
New OBD protocols for Scania S Series EMS10 and PSA vehicles with BlueHDI engines
FGtech EOBD2 now supports the Continental EMS10 / CEM1 Scania ECU in OBD. The reading of the ECU EDC17C60 equipped on 1.4 & 1.6HDI engines is also available in OBD Full. Now you can work on the new generation Scania vehicles, as well as those of the PSA group in...
New Benchmode for Ecu Delco equipped on GM and Opel.
FGtech EOBD2 now supports Delco ECUs in benchmode. Now you can work on Opel & GM vehicles safely and quickly. Many more Benchmode and OBD Full are coming for this type of Ecu! Total reading (2m) and writing (1m) (Flash + Eeprom), Checksum, Recovery. Supported Ecu...
New innovative documentation interface for your EOBD2!
Great news! FGTechnology presents the new innovative manual for consulting the ECU instructions by searching for the vehicle model or direct search. The mobile version is available worldwide exclusively for all our customers. Watch the introductory video on Youtube...
GREAT NEWS! New graphic interface for your EOBD2
Great news! FGTech EOBD2 software completely revolutionizes its graphical user interface to improve the experience and efficiency. This new look will make the software easy to use while retaining in some respects a classic and professional style. Multiple functions...
New OBD Full protocols for 1.5 dCi engines equipped on Renault, Nissan & Dacia.
FGtech EOBD2 now supports the Siemens Sid310 control unit in OBD Full. Now you can work on Renault, Nissan, Dacia & Opel vehicles equipped with a 1.5 dCi engine from 2012 to 2019 in safety and speed through diagnostic socket. Many more Benchmode and OBD Full for...
New bench protocols for 1.5 Cdi engines equipped on Mercedes.
FGtech EOBD2 now supports the Siemens SID307 and Sid310 control unit in benchmode. Now you can work on Mercedes and Infiniti vehicles equipped with a 1.5 Cdi engine from 2012 to 2018 in safety and speed. Many more Benchmode and OBD Full for this type of Ecu are...
AUTOPROMOTEC 2022
We are delighted to invite you to visit us in Bologna at the AUTOPROMOTEC Exhibition on May 25th-28th 2022! ? Our FGTech Team will be available from 9am to 6pm to answer all your questions on our new products, services and features.? Book your free ticket HERE✉...
New Benchmode for Citroen and Peugeot commercial vehicles.
FGtech EOBD2 now supports the Siemens SID208 control unit in benchmode. Now you can work on PSA Group commercial vehicles equipped with a 2.2 HDI engine safely and quickly. Many more Benchmode and OBD Full for this type of Ecu are coming! Read (4m) and write (2m)...
Benchmode for Toyota GT86 and Subaru BRZ now supported.
FGtech EOBD2 now supports the Denso Sh72531 and Sh72530 control unit in benchmode. Now you can work on Toyota and Subaru vehicles equipped with a naturally aspirated 2.0 engine in safety and speed. Also supported are new Bench and Jtag Renesas for petrol and electric...
OBD driver for new tractors from 2019 (Bosch MD1CE101)
FGtech EOBD2 now supports the Bosch MD1CE101 in OBD control unit. Now you can work on over 600 latest generation tractors through the diagnostic socket. Virtual read and write protocol available to make changes in total safety and speed. - Virtual Reading- Writing-...
Exclusive Benchmode for Marelli MM10JA.
FGtech EOBD2 now supports the Magneti Marelli MM10JA control unit in benchmode. Now you can work on Alfa Romeo vehicles equipped with 2.0 Turbo 200/280HP engine in safety and speed. Read (2m) and write (1m) total (Flash+Eeprom Internal+External), Checksum, Clone,...
CUMMINS CM2350-2350B now available in Jtag.
FGtech EOBD2 now supports the Cummins CM2350-2350B ECU in Jtag Nexus. Total read and write (Flash+Eeprom), Checksum, Clone, Recovery.
Benchmode for Volvo/ Renault truck Euro5,6,6D+ now available.
FGtech EOBD2 now supports the TRW EMS2.2, EMS2.3, EMS2.4 control unit in Benchmode. Now you can operate on a wide range of new Euro5-6-6d+ work vehicles in total safety and speed. Total read and write (Flash+Eeprom), Checksum, Clone, Patch & Recovery. List of...
New protocol now available for Peugeot E6d engines.
FGtech EOBD2 now supports DELPHI DCM7.1A and DCM7.1B in Bootmode Aurix. Now you can operate on the new Cars and new Euro6b work vehicles of the PSA group in total safety and speed. Read and write total (Flash+Eeprom) List of supported vehicles: Citroen: C5 2.0 BlueHDI...
Happy New Year FGTechnology Team, new update now available.
FGtech EOBD2 now supports the DELPHI DCM7.1B obd control unit via diagnostic socket. Now you can operate on the new Euro6b work vehicles in total safety and speed. Total reading (Flash+Eeprom); Flash writing. List of supported vehicles: Citroen Jumper 2.2 BlueHDI E6b...
Happy Christmas Holidays FGTechnology Team, Christmas Update Now Online!
FGtech EOBD2 now supports all Bosch MEDC17 motor ECU with bench tricore processors via plug. Now you can operate on a wide range of cars and work vehicles in total safety and comfort without the need to open the ECU. Total Read (Backup); Total write (Flash+Eeprom)....
Ecu Valeo VD46.1 equipped on 1.2THP Puretech NOW AVAILABLE IN OBD!
Now available real read and write to OBD for Ecu Valeo VD46.1 PSA group. You will have the opportunity to operate on the 1.2 THP Puretech engines directly from the diagnosis socket! Download the new EOBD2 version with firmware 71 to access the new protocols!...
Ecu Valeo V46.1x equipped on 1.0 Puretech & 1.2VTI Puretech NOW AVAILABLE IN OBD!
Now available real read and write to OBD for Ecu Valeo V46.11/ V46.12/ V46.13 PSA group. You will have the opportunity to operate on the 1.0 Puretech and 1.2 VTI Puretech engines from 2009 onwards directly from the diagnosis socket! Download the new EOBD2 version...
Ecu DCM6.2c equipped on 2.0l BlueHDI NOW AVAILABLE IN OBD!
Now available real reading and writing to OBD for Ecu DELPHI DCM6.2c PSA group. Vehicle list: Citroen Jumper (U9) 2000 BlueHDI AHP (163) 2015 Citroen Relay (U9) 2000 BlueHDI AHP (163) 2015 Peugeot Boxer (U9) 2000 BlueHDI AHP (163) 2015 Peugeot Manager (U9) 2000...
New Benchmode Denso Renesas for Volvo cars and Checksum upgrades.
FGtech EOBD2 now supports the main Denso engine ECU for the Volvo range with bench renesas processors via plug. Total Read (Backup); Total write (Flash+Eeprom). Added new checksums and new benchmodes for: PSA Edc17c60; PSA Mg1cs042; RENAULT- NISSAN Edc17c84; MERCEDES...
Ecu Denso Renesas now available in benchmode.
FGtech EOBD2 now supports the main Denso engine ECUs with Renesas processors via plug. Now you can operate on a wide range of Asian cars and work vehicles in total safety and comfort without the need to open the ECU. Total reading (Backup); Total write (Flash +...
Added Chinese, Japanese and Korean to EOBD2 software.
New languages available: Added Chinese, Japanese and Korean to the EOBD2 software! - 在EOBD2软件中添加了中文、日文和韩文! - EOBD2ソフトウェアに中国語、日本語、韓国語を追加しました! - EOBD2 소프트웨어에 중국어, 일본어, 한국어를 추가했습니다! ...
Added Russian and Bulgarian to EOBD2 software.
New languages available: Added Russian and Bulgarian to the EOBD2 software! - Добавлены русский и болгарский языки в программное обеспечение EOBD2. - Добавихме руски и български към EOBD2 софтуер. ...
New over-the-counter reading and writing package for AdBlue ecus!
FGtech EOBD2 now supports the main Bosch ECU for benchtop SCR management via plug. Total Read (Backup); Total write (Flash+Eeprom). List of ECU: DCU17HD01 Dodge; Iveco; Isuzu; Freightliner; Peterbilt Tr. DCU17PC Mazda DCU17PC01 Mercedes DCU17PC42 Fiat; Mazda Renault;...
Reading and writing on the bench for Delphi CRD3.x – CRD3P.x Mercedes CDI &BlueTEC.
FGtech EOBD2 now supports all ecus CRD3 - CRD3P at the counter via plug. Total Read (Backup); Total write (Flash+Eeprom); Cloning supported. List of ECU: Delphi CRD3 TC1797 Delphi CRD3.10 TC1797 Delphi CRD3.1R TC1797 Delphi CRD3.2R TC1797 Delphi CRD3.20 TC1797 Delphi...
MD1CE100 Man Truck MY2021 now available.
Exclusively available reading and writing of latest generation ECU BOSCH MD1CE100 in Benchmode. Bench mode will allow you to read and write directly through the connector.- Checksum calculated in writing.- Total reading (Backup).- Total Writing (Flash+Eeprom).* MAN...
MG1CS026, MG1CS032, MG1CA007, MG1CA920 now available.
Exclusively available reading and writing of latest generation ECU BOSCH MG1 in Benchmode. Bench mode will allow you to read and write directly through the connector.- Checksum calculated in writing.- Total reading (Backup).- Writing maps.*MG1CS026 Suzuki: S-Cross,...
Ecu Engine Deutz 2.9L now available in Bench.
Exclusively available reading and writing of Ecu BOSCH MD1CE100C Deutz 2.9L engine in Benchmode. Bench mode will allow you to read and write directly through the connector.- Checksum calculated in writing.- Total reading (Backup).- Writing maps.*Brand: DEUTZ,KRAMER...
Exclusive novelty, BOSCH PSG16 now available over the counter.
Available reading and writing of injection pump BOSCH PSG16 eng. Y20DTH in Benchmode. Bench mode for PSG16 will allow you to read and write directly through the connector.- Checksum calculated in writing.- Total reading (Backup).*Brand: OPEL; SAAB;...
BOSCH EDC16 & MED9 now available in benchmode!
From today available reading and writing of all Bosch EDC16/MED9 control units in Benchmode. Bench mode for EDC16 & MED9 will allow you to do what was once only possible from BDM directly through the connector. Now it is no longer necessary to open them!- Checksum...
Mazda 3 – CX3 1.8 Skyactiv-D now available in OBD.
Now available OBD reading and writing for Ecu Denso S801 equipped on Mazda 3-CX3 with motor 1.8 Skyactiv-D. Optimize your Mazda now!
Ford 1.5l EcoBoost now available in OBD
Now available reading and writing in OBD for Ecu Continental EMS2511 equipped on Ford: C-Max DXA 1.5 EcoBoost 6AT 134KW C-Max DXA 1.5 EcoBoost 6MT 110KW Focus 1.5 EcoBoost 6AT 110KW Focus 1.5 EcoBoost 6AT 134KW Focus 1.5 EcoBoost 6MT 110KW Focus 1.5 EcoBoost 6MT...
SIMOS PCR2.1 now available in Benchmode!
Now available reading and writing in Benchmode for Ecu Continental Simos PCR2.1 equipped on 1.6 TDI VW group vehicles: Remap your VW now! Audi A1 Audi A1 Sportback Audi A3 Audi A3 SportbackSeat Altea Freetrack Seat Altea XL Seat Ibiza Seat Ibiza SC Seat Ibiza ST Seat...
Audi SQ2 2.0 TSI now available!
Now available reading and writing in Bootmode for Ecu Continental Simos 8.10 equipped on Audi SQ2 2.0 TSI. Remap your Audi now!
HUMMER H2 & H3 NOW AVAILABLE IN OBD!
Now available obd reading and writing for Ecu DELPHI P12 equipped on HUMMER H2 & H3 (3.5l,6l). New version available. Remap your Hummer now!
PSA 2.0l BlueHDI NOW AVAILABLE IN OBD!
Now available real reading and writing to OBD for Ecu DELPHI DCM6.2A PSA group. Vehicle list: Citroen C4 2.0 BlueHDI Citroen C4 Picasso 2.0 BlueHDI Citroen C5 2.0 BlueHDI Citroen DS4 2.0 BlueHDI Citroen DS5 2.0 BlueHDI Citroen Jumpy 2.0 BlueHDI Citroen Picasso 2.0...
NEW BENCHMODE VOLVO XC40 T3 1.5L GASOLINE
New benchmode Plus+ for MG1CS080 ecu equipped on Volvo XC40. Read & write fast over the counter via pinout. Many more ECU available for this extension are coming soon.
NEW BOOTMODE CONTINENTAL SIMOS!
New bootmode for simos 12, 18 and PCR2.1 with Bench Plus+. Automatic password calculation, fast read&write. A lot more ecus will be available with Bench Plus+ extension .
BOSCH MD1CE101 NOW AVAILABLE
Thanks to Bench Plus+, you can read & write flash and eeprom of Bosch MD1CE101 ECU mounted on the new Case, Claas, Fpt Industrial, Iveco, New Holland and Steyr engines. With this extension it is sufficient to remove the control unit and connect it via the pinout,...
BENCHMODE BOSCH MD1/MG1
With the new Bench Plus+ extension you will be able to read & Write the following Bosch MD1/MG1 ECUs: MD1CP001 SPC5777 VAG, Mercedes Benz MD1CP004 SPC5777 VAG MD1CP004 TC298TP VAG MD1CS004 TC298TP VAG MD1CP014 TC298TP VAG MD1CS001 TC298TP BMW, Mini...
NEW BENCH PLUS+!
NEW BENCH PLUS+ Thanks to Bench Plus+, you can read & write flash and eeprom of the new Bosch MD1/MG1 ECUs. With this extension it is sufficient to remove the control unit and connect it via the pinout, without having to solder the boot wire on the microprocessor....